Has moved to www.engageinc.com

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 

 

 

   
 

· T1 Over IP Interconnect for Voice and Data ·

The IPTube•QT1 encapsulates full and fractional T1 and TDM circuits, along with their framing and signaling bits, into IP packets. The IPTube•QT1's T1 Over IP, T1 Over Ethernet connection provides for the transparent interconnection of PBXs, Telecom Switches and T1 based communication systems via LANs, WANs, MANs, Satellite and Wireless Ethernet.
            
                                                                                  IPTubeQT1 Brochure in PDF Format


The IPTube•QT1 is available with one to four T1 interfaces and a 10/100 BaseT Full/Half Duplex Ethernet Interface. The T1 interfaces have configurations that for provide independent protocol, compression, packet sizing, buffering, clocking, framing, coding and channel settings. The protocols supported are IPTube, CESoIP, and HDLCoIP.

Transparent Interconnect
The IPTube•QT1's transparent operation maintains the proprietary signaling required to support PBX features such as call conferencing, call forwarding, caller ID and SS7. Legacy phone equipment investment is preserved. Transparent support for Modem, Fax, or Data circuits. Voice quality is not compromised.

IP Cellullar Back Haul
IPTube•QT1s are used to provide transparent interconnection of the base stations (BTSs), base station controllers (BSCs) and mobile switching centers (MSCs) over IP Ethernet packet-switched networks. Supported access media include fiber, coax and fixed wireless. Cellular phone service providers are able to save substantially by converting to a packet switch network from circuit TDM lease lines. The IPTube•QT1 has the Duplicate packets transmission and reception feature that provides for resilient performance through a lossy interconnect.

Lossless Data Compression
The IPTube•QT1C detects idle/redundant data within each T1 Voice circuit resulting in a as much as a 56 to 1 bandwidth savings. The IPTube•QT1C compression works from the lowest latency setting of 8 T1 frames to the highest setting of 56 T1 frames per packet. TDM Over IP WAN bandwidth is not consumed by silent or redundant circuits and voice quality is not effected.   Note: Compression only supported with IPTube•QT1C model. 


Technical Specifications
IPTubeManual in PDF Format

LAN Network Interface:
• 10/100 BaseT Full/Half Ethernet
• Autonegotiation or Configurable Speed and Duplex

LAN Network Protocols Supported:
• IP, TCP, UDP, ICMP

Duplicate Packet Transmission:

• 1 to 4 Duplicates
Provides for resilient performance through a lossy interconnect.

T1/Fractional T1 Specifications:

· One to Four Port CSU/DSU Models
· Connects directly to T1 Line or to a DS1 with a Crossover Cable
· Framing - ESF or D4
· Coding - B8ZS or AMI
· Supports DS0 assignments from 1 to 24
· DS0 Configuration x-y,z

T1 Over IP Protocol:

• TDM Over IP
• Circuit Extension Services Over IP - CESOIP
• HDLC Over IP - HDLCOIP
• Frames Per Packet from 8 to 56
   • Low Latency Mode:
              1 millisecond - 8 T1 frames
   • Max Payload Mode:
              7 millisecond - 56 T1 frames

Regulatory:
• Safety -IEC60950
• EMC - CFR 47 Part 15 Sub Part B:2002
            EN55022:1994+A1&A2
            EN55024, ICES-003 1997
            CISPR 22 Level A
• Telecom - Part68
• CE

Lossless Data Compression:
• Detects idle and redundant data within each
   DS0 continuously
• Interconnect bandwidth is not consumed by
   silent or redundant data within the voice
   circuits
• Low Latency 8 to 1 Compression
• Maximum Compression setting 56 to 1

Quality of Service Support:
• IP Type of Service (TOS) CLI configurable
• IANA Registered UDP Port 3175
TFTP Online Upgrade Capable (FLASH ROMs)
• IPTube is fully operational during upgrade

TFTP Upgrade Capable (Flash ROMs):
· IPTube is operational during upgrade

Management:
· Telnet support with Edit and Paste Templates
· Console Port for Out of Band Management

· SNMP support (MIB I, MIB II)

· Remote configuration, monitoring, & reset

Console Port:
· RJ45 to DB9 Female DCE adapter shipped with product. Enables direct connection to Com1.

Power:

·
15VDC, 1.6A; International Adapters Available
· 24-36 VDC Optional
· -48 VDC Optional
• Hot Standby with 2nd Power Module

Dimensions:
• 14" (L) x 5.5" (W) x 2.50" (H)

Engage Communication · 9565 Soquel Drive, Aptos, CA 95003
Tel: (831) 688-1021 · Fax: (831) 688-1421 · sales@engageinc.com

© Copyright 1989-2005 Engage Communication, Inc. Engage Communication has moved to WWW.ENGAGEINC.COM